Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
What're your thoughts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move easily; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. Make certain you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to think about using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have actually currently acquired a new tub as well as don't require to transform the setup of your previous water supply pipes.
Your tools as well as material list must consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers are in location between the tap and the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required setting. The wooden boards are handy in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water and inspect all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the producer's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been made use of at the very least once as this will resolve it right into its last position.
Getting ready for the Setup
To start with, the supporting frame provided with the bathroom should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, creating the water to pass through the wall surface between the bath as well as the tiling, bring about complications with wetness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article on How to Install a Bathtub Yourself through a friend on our other web blog. Are you aware of somebody else who is enthusiastic about the subject? Do not hesitate to promote it. I praise you for your time. Visit again soon.
Get Quote Report this page